Anden has the only dehumidifiers that can pull moisture out of the air at lower temperatures to “simulate fall.”
Anden Model Dehumidifiers are designed to dehumidify the air coming into the unit by passing the incoming air over an evaporator coil to drop the air temperature below the dew point of the air. Moisture is removed from the air and drained out of the unit to a common floor or waste drain. The air is then reheated in the condenser coil and exits the unit. These industrial grow room dehumidifier units remove up to 710 pints of moisture per day, and powerfully circulates air within your cultivation space to create a healthy, grow-optimized environment. And it really moves some air for maximum moisture removal. Setup is simple, and humidity is constantly controlled to help prevent crop disease and pests.
VLGR Technology
Let’s take a closer look at VLGR Technology. This sophisticated system modulates the speed of dehumidification based on the precise load conditions of your grow environment, allowing for robust VPD performance across all grow conditions. The variable speed refrigeration system keeps your dehumidifiers running during the challenging late flower stage where single-speed dehumidifiers require frequent defrost cycles. This increases capacity, efficiency, and most importantly, the stability of your grow environment.
The Anden 710 series is the best investment across all grow conditions compared to any dehumidifier available, removing 710 pints of moisture per day at 80°F/60% RH. VLGR technology allows the unit to safely operate on a 30-amp breaker, while competitive options top out at 500 pints before requiring a 50-amp breaker, which will dramatically increase installation costs.
Why use an Anden Dehumidifier?
Energy Efficient - Removes up to 3 liters per kilowatt hour, helping minimize operational costs
Easy Filters - The self-sealing, MERV 11 air filter protects the unit’s vital components, plus it’s easy to replace
Flexible Installation - The pre-installed electrical plug is simple to remove for hard-wired applications. Plus, options for suspended, freestanding, or ducted installation
Safety Checks - Terminals on the dehumidifier make it easy to install a float switch to protect against overflows
Digital Interface - On-board monitoring enables precise settings and simple diagnostics
Remote Control - The included Model A77 remote control measures relative humidity at canopy height for optimum control of your grow environment (upgrade options available), and relays diagnostics from the dehumidifier
Built to Last - Dependability is at the heart of what we do. That’s why we offer a 5-year warranty on this product.
Humidity and Growth
Humidity control is critical. As a cultivator, you know that. Each stage of growth requires an optimized environment. That’s why we recommend keeping humidity under 60% to prevent mold and mildew, and to help plants get the CO2 they need for efficient photosynthesis.
Vapor Pressure Deficit
For optimal indoor growth, don’t forget about VPD. It’s a measure of the difference between vapor pressure in the leaves of your plants and the air surrounding them. Humidity control in the growth environment helps ensure that plants can “breathe” by taking in moisture and letting it out.
The Anden Impact
Anden dehumidifiers put you in control of your growth environment. You get maximum moisture removal and VPD control, with on-board and remote monitoring capabilities to make it all intuitive. Simply put, these grow-optimized products are designed with your plants in mind.
Anden A70 Dehumidifier
This unit delivers industrial-strength dehumidification to micro grow operations, removing 70 pints of moisture per day. It can be programmed to circulate air within your cultivation space, carrying excess moisture away from your crop to prevent fungus, disease, and plant pests. Check below for the full list of industrial specs and grow-optimized features that will set your operation apart.
Anden 70 Specifications
Water Removal 70 Pints/Day
Efficiency 4.4 Pints/kWh
Energy Factor 2.1 Liters/kWh
Power / Current 645 Watts / 5.8 Amps
Part Number A70
Dehumidifier Type Refrigerant Dehumidifier
CFM 200
Operating Temperature 50°-104° F
Supply Voltage 110–120 VAC, 1 Phase, 60 Hz
Unit Dimensions 25" L x 12 1/2" W x 12 1/2" H
Unit Weight 56 lb
Control Type Built-in Digital Control with Display
Air Filter MERV Rating MERV 11
Air Filter Dimensions 98" x 11.75" x 1"
Power Cord 110-120 VAC
Refrigerant Type R410A
Installation Options Suspended, Freestanding, Inlet and Outlet Ducted
Drain Fitting 3/4" MPT x 3/4" barbed
Drain Port Connection 3/4" Threaded MNPT
Warranty 5 Year
Anden Dehumidifier 100
No matter the size, every successful grow operation requires professional humidity control. The Anden Model A100 removes 100 pints per day of moisture from the air, helping control humidity in smaller grow spaces. In addition to its capacity, the A100 features integration with smart controls and a 5-year warranty. Don’t trust your harvest to inferior retail units. Anden is the professional’s choice for true humidity control.
Anden 100 Specifications
Water Removal 100 Pints/Day
Efficiency 5.5 Pints/kWh
Energy Factor 2.6 Liters/kWh
Power / Current Draw 750 Watts / 6.9 Amps
Part Number A100
Dehumidifier Type Refrigerant Dehumidifier
CFM 280
Operating Temperature 40°-140° F
Supply Voltage 110–120 VAC, 1 Phase, 60 Hz
Unit Dimensions 26" L x 14" W x 15" H
Unit Weight 64 lb
Control Type Built-in Digital Control with Display
Air Filter MERV Rating MERV 11
Air Filter Dimensions 11 22/25" x 13 1/2" x 1"
Power Cord 110-120 VAC
Refrigerant Type R410A
Installation Options Suspended, Inlet and Outlet Ducted
Drain Fitting 3/4" MPT x 3/4" barbed
Drain Port Connection 3/4" Threaded MNPT
Warranty 5 Year
Anden A100F Dehumidifier
No matter the size, every successful grow operation requires professional humidity control. The Anden Model A100F removes 100 pints per day of moisture from the air, helping control humidity in smaller grow spaces. In addition to its capacity, the A100F features integration with smart controls and a 5-year warranty. Don’t trust your harvest to inferior retail units. Anden is the professional’s choice for true humidity control.
Anden 100F Specifications
Water Removal 100 Pints/Day
Efficiency 5.5 Pints/kWh
Energy Factor 2.6 Liters/kWh
Power / Current Draw 750 Watts / 6.9 Amps
Part Number A100F
Dehumidifier Type Refrigerant Dehumidifier
CFM 280
Operating Temperature 50°-104° F
Supply Voltage 110–120 VAC, 1 Phase, 60 Hz
Unit Dimensions 26" L x 14" W x 18" H
Unit Weight 64 lb
Control Type Built-in Digital Control with Display
Air Filter MERV Rating MERV 11
Air Filter Dimensions 11.88" x 13.5" x 1"
Power Cord 110-120 VAC
Refrigerant Type R410A
Installation Options Freestanding
Drain Fitting 3/4" MPT x 3/4" barbed
Drain Port Connection 3/4" Threaded MNPT
Warranty 5 Year
Anden Dehumidifier 130
Grow environments require high-capacity, specially designed dehumidifiers to control humidity and protect crops. The Anden 130 delivers performance, capacity and reliability that is not available from the portable units sold via retail. With 130 pints per day removal capacity, integration with smart controls and a 5-year warranty, you can trust Anden to protect your crop.
Anden 130 Specifications
Water Removal 130 Pints/Day
Efficiency 5.9 Pints/kWh
Energy Factor 2.8 Liters/kWh
Power / Current 920 Watts / 8.3 Amps
Part Number A130
Dehumidifier Type Refrigerant Dehumidifier
CFM 310
Operating Temperature 40°-104° F
Supply Voltage 110–120 VAC, 1 Phase, 60 Hz
Unit Dimensions 30 1/16" L x 19 1/2" W x 18 3/4" H
Unit Weight 113 lb
Control Type Built-in Digital Control with Display
Air Filter MERV Rating MERV 11
Air Filter Dimensions 14" x 19" x 1"
Power Cord 110-120 VAC
Refrigerant Type R410A
Installation Options Suspended, Inlet and Outlet Ducted
Drain Fitting 3/4" MPT x 3/4" barbed
Drain Port Connection 3/4" Threaded MNPT
Warranty 5 Year
Humidity and Growth
Humidity control is critical. As a cultivator, you know that. Each stage of growth requires an optimized environment. That’s why we recommend keeping humidity under 60% to prevent mold and mildew, and to help plants get the CO2 they need for efficient photosynthesis.
Vapor Pressure Deficit
For optimal indoor growth, don’t forget about VPD. It’s a measure of the difference between vapor pressure in the leaves of your plants and the air surrounding them. Humidity control in the growth environment helps ensure that plants can “breathe” by taking in moisture and letting it out.
The Anden Impact
Anden dehumidifiers put you in control of your growth environment. You get maximum moisture removal and VPD control, with on-board and remote monitoring capabilities to make it all intuitive. Simply put, these grow-optimized products are designed with your plants in mind.
Anden Dehumidifier 130F
Grow environments require high-capacity, specially designed dehumidifiers to control humidity and protect crops. The Anden 130F delivers performance, capacity and reliability that is not available from the portable units sold via retail. With 130 pints per day removal capacity, integration with smart controls and a 5-year warranty, you can trust Anden to protect your crop.
Anden 130F Specifications
Water Removal 130 Pints/Day
Efficiency 5.9 Pints/kWh
Energy Factor 2.8 Liters/kWh
Power / Current Draw 920 Watts / 8.3 Amps
Part Number A130F
Dehumidifier Type Refrigerant Dehumidifier
CFM 310
Operating Temperature 40°-140° F
Supply Voltage 110–120 VAC, 1 Phase, 60 Hz
Unit Dimensions 26" L x 14" W x 15" H
Unit Weight 64 lb
Control Type Built-in Digital Control with Display
Air Filter MERV Rating MERV 11
Air Filter Dimensions 16" x 19" x 1"
Power Cord 110-120 VAC
Refrigerant Type R410A
Installation Options Freestanding
Drain Fitting 3/4" MPT x 3/4" barbed
Drain Port Connection 3/4" Threaded MNPT
Warranty 5 Year
Anden Dehumidifier 210
The Anden A210V1 dehumidifier are designed and built for cultivation. This industrial grow room dehumidifier removes up to 210 pints of moisture per day, and circulates air within your cultivation space to create a healthy, grow-optimized environment. Setup is simple, and humidity is constantly controlled to help prevent crop disease and pests.
Anden 210 Specifications
Water Removal 210 Pints/Day
Efficiency 6.3 Pints/kWh
Energy Factor 3.0 Liters/kWh
Power / Current 1,450 Watts / 7.1 Amps
Part Number A210V1
Dehumidifier Type Refrigerant Dehumidifier
CFM 525
Operating Temperature 50°-104° F
Supply Voltage 208-240 VAC, 1 Phase, 60 Hz
Unit Dimensions 30 1/8" L x 19 1/2" W x 18 3/4" H
Unit Weight 118 lb
Control Type Built-in Digital Control with Display
Air Filter MERV Rating MERV 11
Air Filter Dimensions 14" x 18" x 2"
Power Cord SJT, 6-15P
Refrigerant Type R410A
Installation Options Suspended, Freestanding, Inlet and Outlet Ducted
Drain Fitting 3/4" MPT x 3/4" barbed
Drain Port Connection 3/4" Threaded MNPT
Warranty 5 Year
Anden Dehumidifier A320V1
Anden A320V1 dehumidifiers are designed and built for cultivation. This industrial unit removes up to 320 pints of moisture per day, and powerfully circulates air within your cultivation space to create a healthy, grow-optimized environment. And it really moves some air--up to 830 cubic feet per minute for maximum moisture removal. Setup is simple, and humidity is constantly controlled to help prevent crop disease and pests.
Anden A320V1 Specifications
Water Removal 320 Pints/Day
Efficiency 6.0 Pints/kWh
Energy Factor 2.9 Liters/kWh
Power / Current 750 Watts / 11.1 Amps
Part Number A320V1
Dehumidifier Type Refrigerant Dehumidifier
CFM 830
Operating Temperature 50°-104° F
Supply Voltage 208-240 VAC, 1 Phase, 60 Hz
Unit Dimensions 24 1/4" L x 32 5/8" W x 24" H
Unit Weight 180 lb
Control Type Built-in Digital Control with Display
Air Filter MERV Rating MERV 11
Air Filter Dimensions 20" x 22" x 2"
Power Cord SJT, 6-20P
Refrigerant Type R410A
Installation Options Suspended, Freestanding, Inlet and Outlet Ducted
Drain Fitting 3/4" MPT x 3/4" barbed
Drain Port Connection 3/4" Threaded FNPT
Warranty 5 Year
Anden Dehumidifier A320V3
Anden A320V3 is designed and built for cultivation. This industrial grow room dehumidifier unit removes up to 320 pints of moisture per day, and powerfully circulates air within your cultivation space to create a healthy, grow-optimized environment. And it really moves some air--up to 830 cubic feet per minute for maximum moisture removal. Setup is simple, and humidity is constantly controlled to help prevent crop disease and pests.
Anden A320V3 Specifications
Water Removal 320 Pints/Day
Efficiency 5.5 Pints/kWh
Energy Factor 2.6 Liters/kWh
Power / Current 2,450 Watts / 9.2 Amps
Part Number A320V3
Dehumidifier Type Refrigerant Dehumidifier
CFM 830
Operating Temperature 50°-104° F
Supply Voltage 220–240 VAC, 1 Phase, 60 Hz
Unit Dimensions 24 1/4" L x 32 5/8" W x 24" H
Unit Weight 180 lb
Control Type Built-in Digital Control with Display
Air Filter MERV Rating MERV 11
Air Filter Dimensions 20" x 22" x 2"
Power Cord SJT, L7-20P
Refrigerant Type R410A
Installation Options Suspended, Freestanding, Inlet and Outlet Ducted
Drain Fitting 3/4" MNPT x 3/4" barbed
Drain Port Connection 3/4" Threaded FNPT
Warranty 5 Year
Anden Dehumidifier 710V1
The Anden A710V1 Dehumidifier is designed for cultivation from the ground up. It utilizes innovative Variable-Speed, Low Grain Refrigerant Technology (VLGR patent pending) to deliver maximum performance and efficiency throughout the grow cycle. That means you can maximize your moisture removal capacity and maintain tight control over Vapor Pressure Deficit during late flower cultivation by modulating the refrigeration system to match the load.
Anden Dehumidifier 710V1
Water Removal 710 Pints/Day
Efficiency 6.35 Pints/kWh
Energy Factor 3.0 Liters/kWh
Power / Current Draw 4,706 Watts / 19.6 Amps
Part Number A710V1
Dehumidifier Type Refrigerant Dehumidifier
CFM 1,760
Operating Temperature 50°-104° F
Supply Voltage 208-240 VAC, 1 Phase, 60 Hz
Unit Dimensions 31 23/32" L x 44 7/8" W x 34 13/32" L
Unit Weight 360 lb
Control Type Built-in Digital Control with Display
Air Filter MERV Rating MERV 11
Air Filter Dimensions 29.5" x 31.5" x 1.75"
Power Cord SJT, L6-30P
Refrigerant Type R410A
Installation Options Suspended, Freestanding, Inlet and Outlet Ducted
Drain Fitting 3/4" MNPT x 3/4" barbed
Drain Port Connection 3/4" Threaded FNPT
Warranty 5 Year
Anden Dehumidifier 710V3
The Anden A710V3 Dehumidifier is designed for cultivation from the ground up. It utilizes innovative Variable-Speed, Low Grain Refrigerant Technology (VLGR patent pending) to deliver maximum performance and efficiency throughout the grow cycle. That means you can maximize your moisture removal capacity and maintain tight control over Vapor Pressure Deficit during late flower cultivation by modulating the refrigeration system to match the load.
Anden 710V3 Specifications
Water Removal 710 Pints/Day
Efficiency 6.35 Pints/kWh
Energy Factor 3.0 Liters/kWh
Power / Current 4,820 Watts / 17.4 Amps
Part Number A710V3
Dehumidifier Type Refrigerant Dehumidifier
CFM 1,760
Operating Temperature 50°-104° F
Supply Voltage 277 VAC, 1 Phase, 60 Hz
Unit Dimensions 31 23/32" L x 44 7/8" W x 38" H
Unit Weight 360 lb
Control Type Built-in Digital Control with Display
Air Filter MERV Rating MERV 11
Air Filter Dimensions 19.5" x 31.5" x 1.75"
Power Cord SJT, L7-30P
Refrigerant Type R410A
Installation Options Suspended, Freestanding, Inlet and Outlet Ducted
We don't have a video for this product yet. Questions? Our grow experts are here to help: 888-815-9763.
How does the Anden 320 Pint Dehumidifier compare to Quest?
Anden and Quest are both made by the same parent company (Therma-Stor) and carry the same warranty and USA manufacturing — the difference is positioning. Quest leads on energy efficiency and commands a higher price; Anden is the value option at a lower price point, well suited for growers who need a solid, reliable dehumidifier without paying for Quest's efficiency premium.
Can this unit be daisy-chained with other units?
Yes. Anden units use a true dry contact and need to be positioned first in a daisy chain — Quest units pass power through their contacts to the next unit, so if mixing brands in one chain, put the Anden unit(s) first.
How should this unit be positioned in a grow room?
Face the filter side toward the wall so it pulls moist air off the wall, and let it blow dehumidified air out over the canopy. If installing multiple units, staggering them around the room generally gives more even coverage than clustering them.
