Keep Your Plant Striving For New Heights
Cutting Edge Solutions' Uncle John's Blend is a complex Potassium formula that is used primarily to enhance a plant's metabolic rate, especially for flowering plants during the blooming stage.
Potassium is a major component in photosynthetic processes, including the production of ATP (plant sugars) and the transfer of those sugars throughout the plant tissue. Potassium also helps regulate C02 uptake, as well as playing a major role in the regulation of plants. The low molecular weight of UJB makes it very available to the plant for immediate use, as well as making a very "clean" foliar spray that will not leave heavy built-up or residue on the plant tissue. Uncle John's Blend can also be used in conjunction with CES's 2 other additives Plant Amp and Mag Amp for custom foliar applications.
Uncle John's Blend can be used throughout the entire growth cycle, but is more critical in the flowering stages of a plant's life to maintain energy levels and maximize plant growth. A plant is essentially "dying" as it goes to fruit or seed, adding UJB helps to maintain the metabolic rate of plants that are in some cases not producing as much ATP towards the end of its blooming/fruiting stage.
Uncle Johns Blend is designed for use in hydroponics, soilless, continuous feed, drain to waste, and for use in soil growing applications.
**Note**This Product Not Sold In Oregon. If you are residing in Oregon, click here for Uncle John's Blend Oregon Label!Commercial and small sizes available:
- 1 Quart
- 1 gallon
- 2.5 gallon
- 6 gallon
- 15 gallon
- 55 gallon barrel
- 270 gallon tote
*Please expect a 2-week lead time on placing commercial-sized orders.Guaranteed Analysis
- Potassium (K) 2.0%
- Derived from Potassium Sulfate Iron (Fe) 0.1%
- Derived from Ferrous SulfateMixing Instructions
Directions For Use
- For Hydroponics, foliar feeding, and soil applications:
- 10 ml Uncle John's Blend per gallon of water
This is a highly concentrated solution. Never mix undiluted concentrates, as this may result in nutrient lock-up. Add each nutrient consecutively, allowing ample time for each concentrate used to thoroughly dilute and mix into the water. If preparing a nutrient stock tank, to be used over a period of time exceeding 24 hours, you must aerate nutrient reservoir regularly.
- Shake well and measure carefully using a milliliter measuring cup.
- If using Micro 6-0-0™, add Micro 6-0-0™ first to water, then other nutrients.
- After nutrients are mixed in water, adjust pH to 4.5-6.5. If your pH naturally falls within these parameters, pH adjustment is not necessary.
- Monitor ppm and EC in reservoir and top off with fresh water as needed. Reservoir temperature should be 60-68 degrees F.
- Do not store product in direct sunlight. Do not freeze.
- Product Q&A
Cutting Edge Solutions Uncle John's Blend Questions & Answers
Does your product work with all mediums?
Yes. Cutting Edge Solutions products have been developed wth a very broad range of variables, from water sources to varying types of medium and growing methods. Through our experience with these differences we have achieved a final formula that is effective when used across a wide spectrum of methods.
How long should I go between tank changes?
Tank change intervals depend on the size of your reservoir, and whether or not you are using a drain to waste or recirculating watering system. The average life span of a reservoir is about 5-7 days. When using drain to waste it is best to check your PPM/EC level as the nutrient solution is used to make sure that there is no spike in the PPM/EC, but usually the plants will use the fertilizer as they grow. It is more critical to check your nutrient solution while utilizing a recirculating system, as the runoff can drastically change the PPM/EC level of your nutrient solution. If your PPM/EC is raising in your re-circulating reservoir, you should top it off with plain water until your meter shows an acceptable level.
The size of a plant or the growth stage can determine the rate of water usage and nutrient uptake. Logically, the larger the plant gets, the more water and nutrient it will use. Some short-term crop plants (tomatoes, lettuce) go through an aggressive nutrient uptake around the 3-5 week period, so make sure to keep up on tank changes/monitoring during this critical time period.
Is a transition period necessary between the vegetative and bloom stage?
Depending on the type of plant you are growing, a transition mix may be beneficial. Some more hardy plants don’t need to gradually accept a new mix, while some more delicate plants appreciate more subtle changes in its' diet in order to reduce the risk of shock. Slower growing plant varieties may benefit from a transition period more than a faster growing variety as well. Some plants are naturally more efficient at taking up Iron and don’t require a transition stage.
What is the optimal Ph level for my nutrient solution?
The optimum Ph level for maximum nutrient availability is different for all elements, for instance Nitrogen has a different optimal Ph range than Phosphorus. The optimal Ph range can also vary due to medium and growing method variances, that is to say soil vs. rockwool or Aeroponics vs. Ebb and Flow. Therefore, we recommend a Ph range that is most inclusive, from 4.5 to 6.5. The Ph level we recommend for the most inclusive beneficial range is 6.
We do not recommend using Ph up at any time. If your water is acidic, i.e. RO water, adjust your water to Ph 7.0, then add nutrients. Utilizing this method, the elements are less likely to be locked out because of a severe Ph swing.
What PPM/EC is optimum for my nutrient solution?
PPM levels vary from situation to situation. Our recommended vegetative mixing rate can run as high as 2000 PPM, while a “flush” mixing rate is much lower. Please refer to the CES product mixing and reference chart for specific recommended PPM ranges for our products. Note: Our mixing chart is based on a 0 PPM water source, please test your water to establish your specific base range.
- Tech Specs