Built for professional extraction technicians, the Rosin TRP has the ability to press large rosin batches at the lowest temperatures to preserve rich, valuable terpenes. The Rosin TRP is compatible with manual, air and electric pumps. Pumps can be purchased from Triminator separately.
The Rosin Roller is the first rosin extractor designed specifically for large scale production. The Traditional rosin press design applies pressure to dual heated plates. This causes a limitation for commercial scale production as when plates sizes increase to accommodate more material, the larger surface significantly reduces pressure. Additionally, large place sizes cause the oil to degrade as during pressing it sits on heated plates, unable to escape.
As such, we concluded early on that the key to large scale production is to create a continuous feed of small bath presses. As we developed and tested this technology, we have found not only an increase in speed of production, but a significant increase in yield per press. By pushing the oil out in one direction we are able to capture a higher percentage of essential oils.
The Rosin Roller is built with 5 inch stainless steel rollers. Fully adjustable pressure range operating between 500LB to 3000LB per square inch. Since the contact point of the rollers is a thin line, not a large plate surface, we are able to achieve much higher pressure with less applied force.
Hundreds of finite element analysis simulations were conducted while designing the frame to be capable of withstanding up to 25 tons of pressure. There is 1235 effective PSI of pressure and 833 PSI of virtual pressure with the Rosin TRP.
That not enough? check out the Triminator TRP Stack for all the same features with more power!
By offering high pressure users can press rosin at lower temperatures to maintain valuable terpene content in the end product.
6 inch to 10 inch platen offer more platen space to provide the most versatility in commercial use for both flower flower and pollen while maintaining a short distance for the oil to travel.
Big size aluminum platen provides homogeneous temperatures and high reserves of energy for the most optimal heat transfer.
These plates are also food grade, keeping your rosin free and protected from harmful materials and chemicals.
The Triminator Rosin Press TRP provides easy access and increased visibility of the product so that technicians can view the progress of their squeeze from start to finish.
Dual PID temperature control allows you to set the exact temperature preference for each plate.
Pump not included. Must be purchased separately to operate press. Air or electric pump options available. Customers that purchase Rosin Presses with air/hydraulic pump will need an external source of compressed air to operate.
|Lead Time||This product ships in 1-2 Business Days|
|Rosin Press Type||Hydraulic|
|Plate Size||6" x 10"|
|Plate Material Type||Aluminum|
|Temperature Range||0-225 F|
|Max. Pressure||25 Tons|
|Adjustable Tilt Position||No|
|Needs Air Compressor||Required|
|Power Cord(s) Included||Yes|
Yields range significantly and depend largely on the quality of the materials used.
Note: Adequate application of pressure is important to achieve optimal yields and these figures are based on averages tests. Results may vary and depend heavily on your material as well as the operator.
Depending on your material, the proper micron bags are suggested but results will always vary.
For dry sift and ice water extractions use a 36 micron or 72-micron bag. 72-micron rosin bags will offer higher yields compared to 36-micron rosin bags, but the 36-micron bags will provide the highest quality product.
For flower, trim, and shake, use a 115 micron or 90-micron bag. You will get the highest yield from a 115-micron rosin bag compared with a 90-micron rosin bag, but the 90-micron bags will give you more filtration and slightly higher quality product.
There is no magic number for how much you need to press but most people use the formula of press pounds/plate surface area.
For example: A 10-ton press = 20,000 lbs. If you have a 3"x5" plate = 15 square inch. Hence, 20,000/15 = 1,333 PSI
Note: These numbers serve as a guide only. Results will always vary depending on temperature and material as well the press you choose. Refer to manufacturers recommendations for best results.
Expert Advice Toll-Free
© 2011-2023 Hydrobuilder.com - 500 Orient Street Suite 150, Chico, CA 95928 USA
All trademarks and trade names are the property of their respective trademark holders.