Titan Controls Product Documents
The Titan Controls Atlas 3: Day/Night CO2 Monitor/Controller is one of the best ways to control grow room CO2. Maintaining the ideal grow room environment is absolutely essential to cultivating huge, potent plants, and maintaining proper carbon dioxide levels plays a huge role in this. If your plants don't have enough CO2, your harvest will be dismal. But, if there is too much CO2 in the grow room, it creates dangerous conditions. That's where this controller comes in.
Controlling Grow Room CO2 With The Titan Controls Atlas 3
The Titan Controls Atlas 3: Day/Night CO2 Monitor/Controller works between 0-2,000 PPM, and is incredibly east to setup and operate. It works best with Titan Controls CO2 devices, and can control both tank and regulator kits & CO2 generators. No matter how you supplement your grow with CO2, this is the controller/monitor you need.
With an rust, dust, and moisture resistant enclosure, this device is built to withstand the harsher conditions of a grow room. It will last you YEARS of trouble free growing, and it's super efficient. IT operates on a 120 volt power cord at 60 HZ, and just 5 amps. Here are some of the features you should know about.
Features Of The Titan Controls Atlas 3: Day/Night CO2 Monitor/Controller
- Controls CO2 from 200 to 2000 parts per million (PPM)
- Monitors CO2 from 300 to 5000 PPM
- Adjustable PPM hysteresis/differential
- Controls both CO2 tanks or CO2 generators
- CO2 enrichment, or CO2 exhaust features.
- ETL listed for use in commercial applications
- 5 Amps/120 Volts/60 Hz.
- 2 year warranty.
How much CO2 does my grow need?
To determine how much CO2 your grow room needs, you can use our super-simple CO2 calculator. Simply input your room dimensions, along with the ambient CO2 level and your target CO2 level. Then, put in your usage rate in minutes/hour, and we'll pop out the ideal flow rate we think you should use. It's that easy!
- Tech Specs
Brand Titan Controls SKU HGC702608 Weight (lb.) 1.75 Lead Time Due to social distancing requirements, this product ships in 7-10 Business Days Length (in.) 10.8 Width (in.) 5.5 Height (in.) 4.1 Warranty 2 Year Prop 65 No UPC 847127000908 UL Listed No CO2 Sensor Type Integrated CO2 Sensor Number of Zones Single Zone Has Photocell No Amps 5 Voltage 120 Volts
Titan Controls Atlas 3: Day/Night CO2 Monitor/Controller Videos
- Product Q&A
Titan Controls Atlas 3: Day/Night CO2 Monitor/Controller Questions & Answers
Q: Can Sulphur vaporization can damage my controller?
A: Yes. To protect your controller, it is important to disconnect and cover the Atlas 3 by wrapping with a plastic bag OR remove the controller from the grow area while using sulphur vaporizers in your grow room. Titan Controls can analyze and detect CO2 components that have been contaminated and damaged by sulphur vaporization. We reserve the right to not repair these defective units under warranty, however we can repair and return your Atlas 3 for a fee, if you would like.
Q: Does my Titan controller need to be calibrated?
A: No, your controller has been factory calibrated and is ready for service when you take it out of the box. Each unit will provide years of use and will maintain its settings without any further changes required. Please contact us if you think that your calibration is not correct and we can help you out.
Q: My CO2 monitor/controller is reading really high all the time. What's wrong with it?
A: We hear this a lot. The main issue is the 2000 ppm of CO2 we exhale when we're breathing. If you're in your room and you see that the ppm is high, leave the area for an hour or so and turn off your CO2 source, then peek your head in and check the reading, it should be reading under 1000 ppm mattering on how well your room is sealed. After observing your CO2 Monitor/Controller for awhile, you'll start to see what your normal ppm level is in your room. The normal outdoor ppm is 400 ppm to 600 ppm based on where you live (city vs. rural).
Q: Should I run my CO2 at night?
A: No, you shouldn't. Plants photosynthesize CO2 only during the daylight hours. At night, the plants expire CO2 and have no use for CO2. So, save yourself some money and only dose CO2 during daylight hours when it does the most good for the plants.
Q: I'm getting "Er.1" showing on my Atlas 3 LCD display. What does it mean?
A: This is 'Error Code 1' for the Atlas 3. This is a problem with the CO2 sensor in the controller. To fix it, just turn off the power, wait five seconds and then reactivate the controller. This should take care of it. If not, give us a call at 888-808-4826 and we'll help you out.
Q: I'm getting "Er.8" showing alternately with the sensor values on my Atlas 3 LCD display. What does it mean?
A: This is 'Error Code 8' for the Atlas 3. This is a memory corruption problem and all your preferred settings will be reset to the default factory settings. To fix it, re-enter your preferred settings and this should take care of it. If not, give us a call at 888-808-4826 and we'll help you out.
Q: What Growing Media Can I Use Hygrozyme In?
A: You can use Hygrozyme in all soilless and soil medias. That being said, we do not recommend the use of Hygrozyme in your Aquaponics system.
Q: What is the maximum square feet that the CO2 sensor is most effective?
A: The maximum square footage that is recommended for use of the sensor is 400 square feet. It may be used in larger areas, however the reaction time for the controller will be extended.
Titan Controls Atlas 3: Day/Night CO2 Monitor/Controller Reviews
- easy to use
Easy to setup in my room. I'm using this with an Ares 2 CO2 generator and it's controlling it correctly. very simple