Professionals looking for a product with the highest possible mold resistant rating should look no further!
IAQ 6000 GEN3 is a next generation VOC compliant product that is formulated with a unique fungistatic agent to resist mold growth on the dry coating surface. IAQ 6000 GEN3 is a white, tintable and durable 100% acrylic water based coating for professional use. IAQ 6000 GEN3 has successfully passed ASTM G-21 mold resistance testing with the highest possible score.
IAQ 6000 GEN3 is recommended for use on wood, plaster, wallboard, sheetrock, concrete, masonry block, primed metal and galvanized metal.
*Resists mold on the dry coating surface only
IAQ 6000 GEN3 Features
When addressing mold and water damage, you need to make sure you get lasting results. That’s why pros in the remediation business adhere to industry best practices which include a three step process: Clean. Kill. Coat. Fiberlock provides the most complete, most effective products to ensure that mold and water damage issues are remediated and that your investment, health, and safety are protected.
Fiberlock's IAQ 6000 GEN3 Zero VOC Mold Coating is step 3 in Fiberlocks "Clean. Kill. Coat." process. Learn about part one Fiberlock Technologies IAQ Advanced Peroxide Cleaner, here! Check out Part two, "Shockwave" here!
Surfaces to be coated must be free of dust, dirt, grease, loose paint, oil, glue size, calcimine, wax, soap and other surface contamination. Clean mold stained surfaces with IAQ Advanced Peroxide Cleaner, or use an EPA registered antimicrobial disinfectant cleaner such as IAQ 2000, IAQ 2500, ShockWave or ShockWave RTU. Patch irregularities with vinyl patching paste or an appropriate patching compound. IAQ 6000 GEN3 is self-priming over bare sheetrock, composition board, ceiling tile and concrete.
WALLBOARD, SHEETROCK, GYPSUM BOARD
Joint cement should be sanded smooth, but avoid abrading the paper.
Apply IAQ 6000 GEN3 with a brush, roller or airless spray equipment.
IAQ 6000 GEN3 may be tinted to any off-white or pastel based color. Add up to 2 oz. of universal colorant per gallon. Start with 50% of the tinting formula and adjust as necessary.
IAQ 6000 GEN3 is supplied ready to use, but can be thinned sparingly with water (up to 1/2 pint water per gallon) for proper application consistency if necessary. Apply IAQ 6000 GEN3 generously and uniformly by brush, roller, or airless spray. Apply one coat of IAQ 6000 GEN3 and ensure that the finished surface is properly sealed. To ensure that the finished surface is properly sealed, two-coats may be required on some porous surfaces.
Clean tools and drippings with warm soapy water before IAQ 6000 GEN3 dries. Dispose of waste according to all existing local, state and federal regulations.
Store in a dry place at temperatures between 40°F (4.5°C) and 90°F. (32°C). Stir thoroughly. Do not mix with any other coatings, solvents or colors in oil. The IAQ 6000 GEN3 coating is resistant to mold only on the surface of the coating. No mold resistance claim is made other than to the coating itself. The use of this product does not protect users or others against food-borne or disease-causing bacteria, viruses, germs or other disease-causing organisms. Do not apply when air or surface temperature is below 50°F (10°C), or when drying conditions are poor or when surfaces are above a 15% moisture level content. Use adequate ventilation during application. When applying with a sprayer, wear a NIOSH approved respirator with any R, P, N or HE filter.
For interior use only.
|Shipping Restrictions||AK, HI|
|Lead Time||This product ships in 7-10 Business Days|
Be the first to review this product
Expert Advice Toll-Free
© 2011-2023 Hydrobuilder.com - 500 Orient Street Suite 150, Chico, CA 95928 USA
All trademarks and trade names are the property of their respective trademark holders.