*For Wet Trimming Only* - All Trimpro Trimmers are designed to be used with wet product only. If used with dry product damage may occur.
The Trimpro Workstation is an effective boutique model trimmer. The Stainless Steel grate is just 1/16 of an inch thick allowing for an even closer cut. The circular hand movements and downward pressure ensures each flower is trimmed to the operators desired level of perfection.
Manual Control For trimming, take a branch of a freshly harvested plant in your hand and move it over the grate with a back-and-forth motion while rotating the plant at the same time. Its tempered steel blade makes a clean cut without damaging the plant. If you would prefer to have the flowers circulated by air, take a look at the Trimpro Automatik series which utilizes a fan and vacuumm to move the flowers over the grate and blade. Or check out the Trimpro Rotor series that utilizes robotic touch manipulation of the folowers to speed up trimming time.
Easy to Use The Trimpro Workstation is easy to use while standing or sitting and gives you tons of control over the end product. By adjusting the blade and the way you manipulate the flowers over the grate you can trim to your desired level and speed. All trimmings are collected for easy disposal or processing in a mesh bag.
Easy to Maintain The blade assembly can be easily removed for sharpening to ensure you always get the cleanest cut. Cleaning the non-stick grate is a breeze. Just spray the grate and blade with isopropyl alcohol between uses to ensure a clean and sharp cut. The unit is easy to disassemble and replacement parts are available here on Hydrobuilder.com.
Trimpro offers a full line of trimming machines of various types and sizes:
The manufacturer does not accept any responsibility for damages caused to or by the trimmers resulting from an inadequate use or assembly. Use the trimmers in accordance with existing laws and regulations.
|Lead Time||This product ships in 1-2 Business Days|
|Trimmer Type||Stand Up|
|Feed Type||Single Branch|
|Production Capability||2-4 lbs/hr|
How Do I clean My Trimpro Machine?
Use a plastic scraper to collect the pollen build-up. Do not use a metal scraper as it might scratch the coating on the grate and the blade. Use a cloth with rubbing alcohol to finish cleaning it.
How Do I Clean My Trimpro Bag?
Soak the bag in warm water, rub off the build-up. You can also soak it in rubbing alcohol for a short amount of time, rub off the residue and simply pass it through some running water to finish cleaning it.
How Do I Adjust The Height Of My Trimpro Blade?
Blade height adjustment instructions can be found for each machine on their respective instruction sheet.
How Often Should I Sharpen My Trimpro Blade?
Trimpro blades are made of tempered steel which makes them very tough and gives them a great lifespan. It is important for the quality of your manicure to keep them sharp. It is manufacturer recommend to have them sharpened every 6 months to every year (highly depending on usage).
How Do I Sharpen My Trimpro Blade?
Sharpening the blade on Trimpro trimmers is a simple process. The most important part of the process is that you should not remove the blade from the hub to which it is attached! The tempered steel blades are balanced on the aluminum hub, allowing optimal operation of the trimmers. If the blade is separated from the hub there is no guaranty that the assembly will be balanced when you put it back into the machine. Sharpening instructions can be found for each machine on their respective instruction sheet.
How Do I Change The Amount Of Air Suction On My Trimpro Machine?
On every machine (except the Rotor) you can bend the flaps upwards to reduce their angle. This creates less air displacement, thus decreasing the amount of suction. You can bend the flaps downwards to increase their angle. This creates more air displacement thus increasing the amount of suction. *CAUTION: When bending the flaps downwards, make sure the flaps do not hit the metal wire brake line.
How Long Is The Warranty On My Trimpro Machine?
There is one year warranty for defective parts. If you are making a warranty claim, please have in hand the serial number engraved on the underside of the frame of the machine.
Sign-up and save! Get exclusive discounts & the latest product releases.
Expert Advice Toll-Free
© 2011-2022 Hydrobuilder.com - 312 Otterson Dr STE D , Chico, CA 95928 USA
All trademarks and trade names are the property of their respective trademark holders.