Thousand Per Hour 512 Pre Roll Cone Machine

Increase Your Daily Cone Output With The Thousand Per Hour 512 Pre Roll Machine!

The Thousand Per Hour 512 Cone Filling Machine is the best piece of equipment for the job when your pre-roll output starts to exceed 3,000 per week. Just as the name suggests, you can pump out 1,000 pre-rolled cones per hour with this machine, with a consistent end result every time.

Constructed from durable, stainless steel and heavy-duty plastic, the TPH 512 will be a reliable part of your arsenal for years to come without slowing down a bit.

The TPH 512 cone filling machine consists of four main parts - It will ship in two separate boxes:

• Main Cradle
• Pop-up Tray
• Plate
• Fill Funnel

Choosing a plate size for your Thousand Per Hour Pre Roll Machine

Unlike many competitors, you can select a plate size for your Thousand Per Hour 512 Pre Roll machine based on the exact cones you plan on using. For example, if you like to use 98mm Raw Cones, or 84mm Original Cones, or any other brand specific cone, you can select that cut. This will ensure maximum accuracy and efficiency of your machine. Available pre-roll plate sizes include:

Custom Plate Sizing

If you don't see the specific plate size you are looking for, reach out to us at 888-815-9763 and we can help you tailor your machine to the exact specifications you need. Thousand Per Hour can manufacture plate sizes to meet whatever cones you would like to use.

How to use the Thousand Per Hour 512 Pre Roll Machine

Step 1: Prepare your feedstock / raw material

The feedstock, or what you actually plan to put into your pre-rolls, is the most important part of your pre-roll process. Making sure you are using quality inputs will ensure quality output. For example, using low quality, a harsh, bad-tasting flower will result in a poor joint, no matter how fancy of a machine you use. Take extra steps to use the finest feedstock, screening out stems and leaves, so that only fine material is put into the blunt plates.

Step 2: Place your blunt plates in the cradle

Your plate should fit inside the cradle snugly, but not so tight that you cannot easily lift the plate out of the cradle after each process.

Step 3: Load your cones into the plate

Start placing your pre-rolled cones into the slots in your plate. This process should take one person approximately 15 minutes, and if you have an extension package, you can have another worker fill your extra plate simultaneously to increase productivity. Lightly tap each cone on the head to get it flush inside the plate.

Step 4: Secure your funnel on the blunt plate

The funnel will help keep any material from spilling out during the loading process, as well as the actual filling process.

Step 5: Weight out your feedstock

For the Thousand Per Hour 512 Pre Roll Machine, you should use 564 grams for a full gram roll, or 307 grams for a half gram roll. Weighing it in advance helps with even distribution, and more accurate weights across the plate.

Step 6: Work the feedstock over the plate

Turn the machine on. As the machine vibrates, work the feedstock around the plate, evenly distributing it over each hole. You should till be operating at a low vibration speed. If you took steps to prepare your feedstock properly, it should be fine enough to easily drop into the holes as you work it around. As material builds up in the corners, use the funnel to help work the material back over the plate.

Step 7: Finish the vibration cycle

Once you have appeared to fill each cone, allow the vibration to continue for a bit longer. This will help pack the cone down, resulting in a higher quality end product.

Step 8: Remove the pre rolls

Using the handles on the side, lift the pop up tray out of the machine carefully, as you don't want to disturb the cones.

Step 9: Quality control of your pre-rolls

Ensure your final product is consistent and meets your standards. Tap each cone lightly to set the crutch, weigh, and close off.

Cleaning the Thousand Per Hour 512 Pre Roll Machine

Cleaning the machine is a breeze, as it can withstand any ethanol based solvent (200 proof or IPA). Simply wipe down the stainless steel surfaces with an appropriate solvent, and use boiling hot water for the cone plate itself to preserve it's integrity.