Optimize the Hardiness of Your Plant and Heighten Resistance to Stress While Amplifying Your Yield
Bulletproof Si is a part of Cutting Edge Solutions Advanced Molecular Family. Bulletproof Si provides silicon in a form (SiO2) that can be utilized in essentially any fertilizer regiment, and since Bulletproof SI is formulated without potassium, application flexiblity is even greater. The silicon form (SiO2) has shown to increase agricultural production, yield, strengthening plants, promote resistance to stressors like heat, cold, drought, lodging, accelerate mitosis, and even helps promote an advantageous upright stature which leads to favorable exposure of leaves to light.
Bulletproof Si has additional natural components including amino acids and Ascophyllum nodosum, facilitating an enhanced uptake, translocation and effectiveness. Bulletproof Si is designed to enhance growth and leaf production in young plants, and can provide mechanical protection in the epidermal root cells, acting as a barrier between the roots and pathogens or parasitic invasions. Bulletproof Si is recommended for use with all Cutting Edge Solutions products, as well as with other commercial hydroponic nutrients.Commercial and small sizes available:
- 1 Quart
- 1 gallon
- 2.5 gallon
- 6 gallon
- 15 gallon
- 55 gallon barrel
- 270 gallon tote
*Please expect a 2-week lead time on placing commercial-sized orders.Guaranteed Analysis
- CONTAINS NON-PLANT FOOD INGREDIENT:
- 5% Silicone Dioxide (Si02) derived from Sodium Silicate
Mild Solutions Mix 1 ml Bulletproof Si ® per gallon of water Higher Strength 1 to 2.5 ml/gallon per gallon of water Maximum Strength 2.5 to 4 ml/gallon per gallon of water
Bulletproof Si should be applied to roots and leaves during all stages of growth.
Use lighter solutions of Bulletproof Si ® for young plants, perennials, and during foliar application. Higher strength solutions are best suited for fast growing annuals, during both vegetative growth and fruiting/flowering.
**NOTE** A strong aroma similar to ammonia is normal in Bulletproof Si. The specialty enzymes used in the formula produce a sour, almost acetic smell. Always shake very well before use.Directions For Use:
Bulletproof Si is a highly concentrated solution. Never mix undiluted concentrates as this may result in nutrient lock-up.
- Add each nutrient separately to water and aerate reservoir regularly. Apply Bulletproof Si to water before any other nutrients.
- Shake well and measure carefully using a milliliter measuring cup. If adding to an already mixed reservoir, ensure Bulletproof Si is diluted in fresh water before adding to fertilizer solution.
- Bulletproof Si ® is strongly alkaline and will raise nutrient solution pH. After nutrients are mixed in water, adjust ph to 5.5-6.5.
- Monitor ppm/EC and pH in reservoir and top off with fresh water as needed.
- Reservoir temperature should be 60-68 degrees F.
- Do not store product in direct sunlight. Do not freeze.
- Product Q&A
Cutting Edge Solutions Bulletproof SI Questions & Answers
Does your product work with all mediums?
Yes. Cutting Edge Solutions products have been developed wth a very broad range of variables, from water sources to varying types of medium and growing methods. Through our experience with these differences we have achieved a final formula that is effective when used across a wide spectrum of methods.
How long should I go between tank changes?
Tank change intervals depend on the size of your reservoir, and whether or not you are using a drain to waste or recirculating watering system. The average life span of a reservoir is about 5-7 days. When using drain to waste it is best to check your PPM/EC level as the nutrient solution is used to make sure that there is no spike in the PPM/EC, but usually the plants will use the fertilizer as they grow. It is more critical to check your nutrient solution while utilizing a recirculating system, as the runoff can drastically change the PPM/EC level of your nutrient solution. If your PPM/EC is raising in your re-circulating reservoir, you should top it off with plain water until your meter shows an acceptable level.
The size of a plant or the growth stage can determine the rate of water usage and nutrient uptake. Logically, the larger the plant gets, the more water and nutrient it will use. Some short-term crop plants (tomatoes, lettuce) go through an aggressive nutrient uptake around the 3-5 week period, so make sure to keep up on tank changes/monitoring during this critical time period.
Is a transition period necessary between the vegetative and bloom stage?
Depending on the type of plant you are growing, a transition mix may be beneficial. Some more hardy plants don’t need to gradually accept a new mix, while some more delicate plants appreciate more subtle changes in its' diet in order to reduce the risk of shock. Slower growing plant varieties may benefit from a transition period more than a faster growing variety as well. Some plants are naturally more efficient at taking up Iron and don’t require a transition stage.
What is the optimal Ph level for my nutrient solution?
The optimum Ph level for maximum nutrient availability is different for all elements, for instance Nitrogen has a different optimal Ph range than Phosphorus. The optimal Ph range can also vary due to medium and growing method variances, that is to say soil vs. rockwool or Aeroponics vs. Ebb and Flow. Therefore, we recommend a Ph range that is most inclusive, from 4.5 to 6.5. The Ph level we recommend for the most inclusive beneficial range is 6.
We do not recommend using Ph up at any time. If your water is acidic, i.e. RO water, adjust your water to Ph 7.0, then add nutrients. Utilizing this method, the elements are less likely to be locked out because of a severe Ph swing.
What PPM/EC is optimum for my nutrient solution?
PPM levels vary from situation to situation. Our recommended vegetative mixing rate can run as high as 2000 PPM, while a “flush” mixing rate is much lower. Please refer to the CES product mixing and reference chart for specific recommended PPM ranges for our products. Note: Our mixing chart is based on a 0 PPM water source, please test your water to establish your specific base range.
- Tech Specs